Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

Battery discharging

Support für alle Mäher-spezifischen Fragen, die nicht unbedingt etwas mit einer Einstellung in Robonect zu tun haben und deshalb nicht zu einem bestimmten Menüpunkt passen.
Antworten
Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Battery discharging

Beitrag von Malmgren »

Hi all.
Sorry if this has been discussed before, I have a hard time searching in german. I have been studying german but only enough to order a leberknödel :D

Anyway, my Robonect is working like a charm. I'm mostly using it via openHAB to get SMS notifications when my AM has got problems (big thanks to @reyem for the binding!). When I get a SMS about the AM being stuck somewhere I can go OUT into my garden and fix the problem and everything is well. The problem is if I'm not able to fix the problem within a number of hours. This seems to lead to the AM battery completely discharging, so it's completely dead. I have to manually put it into the charger and then it asks for time, language, PIN etc like a first time configuration (although it seems my schedules survives this). Before installing the Robonect I didn't have this problem, the AM could be stuck for days without discharging. So I suspect it's the Robonect using up the battery? I tried changing the setting for how long time Robonect should be on after a fault from the default 600 minutes to 30 minutes but it hasn't helped. Anything else I can do?

/Daniel

edit: Just an idea... Could this be because the openHAB binding is polling the API and thus prohibiting Robonect from going to sleep?

viahack
sehr erfahrener Forum-Nutzer
Beiträge: 208
Registriert: Di 26. Jul 2016, 16:08
Wohnort: Schönster Teil Deutschlands
Mäher: Gardena R40Li
Firmware des Mähers (MSW): MSW 2.xx.xx
Herstellungsjahr: 2011
Robonect-Modul: Robonect H30x (Rev.0)
Robonect Firmware: 1.0 beta 5
hat sich bedankt: 4 Male

Re: Battery discharging

Beitrag von viahack »

Hi Malmgren,

I think you are right with the "openHAB" polling.
The mover can not go in sleeping mode.
It is the same, you type on the mover keyboard.
My idea. Stop Polling in Fault Status.
But you loose the WIFI connection.
The WIFI connection come back at Timer start or by push the Stop button.

/ViaHack
Automower: R40Li MSW-Version:2.01.00 MSW-Datum: 2011-09-05 17:32:18 SUB-Version: 2.00.00
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243

Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Re: Battery discharging

Beitrag von Malmgren »

viahack hat geschrieben:
Do 27. Jul 2017, 21:02
My idea. Stop Polling in Fault Status.
I don't think that will work. I mean, when should it start polling again? It will never be able to have any idea about when the problem is fixed, will it? Maybe if it continues to poll but with a much higher frequency (anything above 10 minutes will do with the default Robonect settings I guess).

I filed an issue for the binding, let's see if reyem has any clever ideas ;) https://github.com/reyem/openhab2-addons/issues/9

/Daniel

viahack
sehr erfahrener Forum-Nutzer
Beiträge: 208
Registriert: Di 26. Jul 2016, 16:08
Wohnort: Schönster Teil Deutschlands
Mäher: Gardena R40Li
Firmware des Mähers (MSW): MSW 2.xx.xx
Herstellungsjahr: 2011
Robonect-Modul: Robonect H30x (Rev.0)
Robonect Firmware: 1.0 beta 5
hat sich bedankt: 4 Male

Re: Battery discharging

Beitrag von viahack »

Hi Malmgren,

quick and dirty
A fault reset button in open hub.
Or ping robonect. if robonect answer start polling.

Greeting
Viahack
Automower: R40Li MSW-Version:2.01.00 MSW-Datum: 2011-09-05 17:32:18 SUB-Version: 2.00.00
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243

Antworten

Zurück zu „allgemeine Mäher-Frage?“