I thought I was a good idea to update the mowers firmware. I have a very, VERY old version.
I tried earlier (years ago) to update it, but there was no update program then. Apparently, now there is. However, I get an error:
"FATAL ERROR IN POWERUP
The robotic mower is in an error mode and needs to be restored by installing new software. Press the button below to continue".
After a few pages have been flashing ("downloading firmware"), it returns to this page!
What can I do now?
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
. Testmöglichkeit für das Daily Build.
Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!
.
.
Updating firmware on the mower itself...
- saugbaer
- Forum-Veteran
- Beiträge: 1392
- Registriert: Mo 18. Apr 2016, 01:30
- Wohnort: Ramelsloh
- Mäher: Husqvarna Automower 310
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2022
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: V1.3b (14.06.2022)
- hat sich bedankt: 7 Male
- wurde gedankt: 10 Male
Re: Updating firmware on the mower itself...
Could be at the old firmware
Firmware des Mähers (MSW): MSW 2.xx.xx
p.s
Sign up for Fabian (Admin) by PN
Firmware des Mähers (MSW): MSW 2.xx.xx
p.s
Sign up for Fabian (Admin) by PN
Ich bin nicht die Signatur, ich putz hier nur
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15) HX + APP + VPN + Kamera + LED
- Moskus
- Forum-Anfänger
- Beiträge: 7
- Registriert: Do 29. Jun 2017, 08:58
- Wohnort: Norway
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 2.xx.xx
- Herstellungsjahr: 2011
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 0.9e
- hat sich bedankt: 1 Mal
- Kontaktdaten:
Re: Updating firmware on the mower itself...
Yeah, maybe it's too old. I guess I have to ask Gardena...
I'm not quite sure what this means....
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 208
- Registriert: Di 26. Jul 2016, 16:08
- Wohnort: Schönster Teil Deutschlands
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 2.xx.xx
- Herstellungsjahr: 2011
- Robonect-Modul: Robonect H30x (Rev.0)
- Robonect Firmware: 1.0 beta 5
- hat sich bedankt: 4 Male
Re: Updating firmware on the mower itself...
HI,
Remove the Robonect module.
A Firmware Update for the mover is not tested.
Gruß
ViaHack
Remove the Robonect module.
A Firmware Update for the mover is not tested.
Gruß
ViaHack
Automower: R40Li MSW-Version:2.01.00 MSW-Datum: 2011-09-05 17:32:18 SUB-Version: 2.00.00
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 277
- Registriert: Mo 15. Aug 2016, 00:01
- Mäher: Gardena smart SILENO+
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.2)
- Robonect Firmware: 1.0 beta 6
- wurde gedankt: 1 Mal
Re: Updating firmware on the mower itself...
Is there really a public update for the R40? I know only of the R100/R130 (Sileno/+), both Smart and non-Smart
-
- Forum-Nutzer
- Beiträge: 16
- Registriert: Di 10. Mai 2016, 12:28
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.2)
- Robonect Firmware: V1.0 Beta 7a
Re: Updating firmware on the mower itself...
I also wonder if there is available any firmware update for R40li.
Gardena R40li
- geosshark
- erfahrener Forum-Nutzer
- Beiträge: 59
- Registriert: Di 19. Jul 2016, 11:46
- Wohnort: Dresden
- Mäher: Gardena R40Li
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: 1.2
Re: Updating firmware on the mower itself...
in my opinion the firmware of the R40Li can only updated at factory.
Gruß
Frank
Fritzbox 6490 cable <--> Fritz!WLAN Repeater 450E
R40Li-mit Gleitteller und dem drehbaren Heckrad von Fidatex
"Rob-E" mit Robonect Hx & FW V1.2 > by F. Harder
Frank
Fritzbox 6490 cable <--> Fritz!WLAN Repeater 450E
R40Li-mit Gleitteller und dem drehbaren Heckrad von Fidatex
"Rob-E" mit Robonect Hx & FW V1.2 > by F. Harder