Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

V0.9c can't connect to web console

Gesperrt
manflex58
Forum-Anfänger
Beiträge: 2
Registriert: Di 21. Mär 2017, 18:00
Wohnort: France bOURGOGNE
Mäher: Husqvarna Automower 308
Firmware des Mähers (MSW): MSW 4.xx.xx
Herstellungsjahr: 2014
Robonect-Modul: Robonect Hx (Rev.3)
Robonect Firmware: 1.0beta5

V0.9c can't connect to web console

Beitrag von manflex58 »

Hello,
First of all, sorry I dont speak german, I ll try with my poor english...
I have just received my robonect and played with it for 2 days but here is my problem. After a few minutes (sometimes 2, sometimes 2 hours) the robonect web console is no more accessible via my home box, neither the robonect access point (automower wifi). the only wifi online is the "robonect (zero conf)" which I cannot connect. If I set the power button to OFF, the robonect zero conf wifi stays online (tried during 30 minutes). My only way to reboot the robonect is to disconnect the battery... Then everything is okay, until ...some minutes and then...no more access and only the robonect zero conf wifi is online.
Anybody with this kind of problem ? I know my automower is not up to date (MSW 4), but I dont know if it matters.
Thank you for any help.
Nicolas
Automower 308, Soft 308X, MSW 4.02.00, SUB 4.00.00, MMI 4.02.00

Eike
erfahrener Forum-Nutzer
Beiträge: 68
Registriert: Do 16. Feb 2017, 13:58
Mäher: Husqvarna Automower 105
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.3)
Robonect Firmware: Last

Re: V0.9c can't connect to web console

Beitrag von Eike »

more than 1 access point with the same ssid and password on your ground = known Problem.

if not....its maybe a EOA Part. Fabian will (in this Case send you a new one)


Eike

Admin
Administrator
Beiträge: 2903
Registriert: Di 19. Jan 2016, 18:34
Wohnort: Kiel
Mäher: Gardena SILENO City 500
Firmware des Mähers (MSW): MSW 11.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: stets die Allerneuste :-)
hat sich bedankt: 1 Mal
wurde gedankt: 59 Male
Kontaktdaten:

Re: V0.9c can't connect to web console

Beitrag von Admin »

As eike said: there is a known problem with networks, which consists of two or more access points with the same ssid. Does the module runs stable, when you didn't connect it to your home network?
Do you Häberle possibility to connect it was a unique router / ssid?

(A solution is already in approvement)
Werbefläche zu vermieten. :lol:

manflex58
Forum-Anfänger
Beiträge: 2
Registriert: Di 21. Mär 2017, 18:00
Wohnort: France bOURGOGNE
Mäher: Husqvarna Automower 308
Firmware des Mähers (MSW): MSW 4.xx.xx
Herstellungsjahr: 2014
Robonect-Modul: Robonect Hx (Rev.3)
Robonect Firmware: 1.0beta5

Re: V0.9c can't connect to web console

Beitrag von manflex58 »

Thank you, this is exactly my problem. It worked perfectly since yesterday with only the automower access point. My home ( and garden...) network has multiple wifi access points with same ssid and password. Sounds like the known problem.
Automower 308, Soft 308X, MSW 4.02.00, SUB 4.00.00, MMI 4.02.00

Admin
Administrator
Beiträge: 2903
Registriert: Di 19. Jan 2016, 18:34
Wohnort: Kiel
Mäher: Gardena SILENO City 500
Firmware des Mähers (MSW): MSW 11.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: stets die Allerneuste :-)
hat sich bedankt: 1 Mal
wurde gedankt: 59 Male
Kontaktdaten:

Re: V0.9c can't connect to web console

Beitrag von Admin »

This is my prio 1 task regarding robonect after my holidays.
Werbefläche zu vermieten. :lol:

Gesperrt

Zurück zu „ältere als FW 0.9e“