Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

Battery not loading after upgrading to 1.0 preview

Fehler nur zu dieser Beta-Firmware.
Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Battery not loading after upgrading to 1.0 preview

Beitrag von Malmgren »

Hi all.
As always, I apologize if this has been discussed before...

I upgraded my Robonect to the 1.0 preview today (23.07.2017 version). After that my AM doesn't seem to charge anymore. It's in the charger and says "charging" but the battery percent hasn't gone up. Rather it very slowly goes down. By this rate it will be empty by tomorrow noon, guess that might become a problem. Anyone else recognize the behaviour?

I also like to know, is it safe to downgrade to 0.9e?

/Daniel

Benutzeravatar
saugbaer
Forum-Veteran
Beiträge: 1392
Registriert: Mo 18. Apr 2016, 01:30
Wohnort: Ramelsloh
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2022
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.3b (14.06.2022)
hat sich bedankt: 7 Male
wurde gedankt: 10 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von saugbaer »

Cache problem :idea:
In the browser, press CTRL + F5
:mrgreen: Ich bin nicht die Signatur, ich putz hier nur :mrgreen:
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15)
HX + APP + VPN + Kamera + LED

Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von Malmgren »

saugbaer hat geschrieben:
Sa 29. Jul 2017, 22:49
Cache problem :idea:
In the browser, press CTRL + F5
Nope. Had no effect (other than of course the web page reloading). Also I can't understand how an old cache in my browser could make the AM not charge :shock:

Anyway, when I upgraded the battery was at 37%. Yesterday when I got to bed it was down to 29% and now it's 21%. That's roughly one percent per hour so I get the feeling if I haven't solved this within 21 hours I have a AM that I can't charge anymore.

I've tried restarting the Robonect. The buttons for shutdown and standby are greyed out (maybe that's normal for 1.0?), otherwise I'd test them. Guess next step will be to turn the AM off with the physical power button and wait a while before turning it on again.

/Daniel

Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von Malmgren »

Malmgren hat geschrieben:
So 30. Jul 2017, 08:28
Guess next step will be to turn the AM off with the physical power button and wait a while before turning it on again.
Replying myself here. Tried exactly that and it seems to have sorted the problem out, the percent is now ticking up instead of down.

Should I report the problem somewhere in case it's something Fabian need to solve?

/Daniel

Benutzeravatar
saugbaer
Forum-Veteran
Beiträge: 1392
Registriert: Mo 18. Apr 2016, 01:30
Wohnort: Ramelsloh
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2022
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.3b (14.06.2022)
hat sich bedankt: 7 Male
wurde gedankt: 10 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von saugbaer »

Write Fabian a PN ;)
:mrgreen: Ich bin nicht die Signatur, ich putz hier nur :mrgreen:
AVM 7490 Fw.7.57 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.15)
HX + APP + VPN + Kamera + LED

Der RTler
sehr erfahrener Forum-Nutzer
Beiträge: 156
Registriert: Di 26. Jan 2016, 13:39
Wohnort: Delmenhorst
Mäher: Husqvarna Automower 308X
Firmware des Mähers (MSW): MSW 5.xx.xx
Herstellungsjahr: 2015
Robonect-Modul: Robonect H30x (Rev.0)
Robonect Firmware: V1.0 - Beta7a 15.10.18

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von Der RTler »

Malmgren hat geschrieben:
Sa 29. Jul 2017, 22:34
Hi all.
As always, I apologize if this has been discussed before...

I upgraded my Robonect to the 1.0 preview today (23.07.2017 version). After that my AM doesn't seem to charge anymore. It's in the charger and says "charging" but the battery percent hasn't gone up. Rather it very slowly goes down. By this rate it will be empty by tomorrow noon, guess that might become a problem. Anyone else recognize the behaviour?

I also like to know, is it safe to downgrade to 0.9e?

/Daniel
Hej,

the same problem I had also, after I had installed the FW 1.0 beta for testing. The status was "charging", but the % display was running backwards. Then I reinstalled the FW 0.9e. Since then everything is all right. Perhaps it is only a display error in the FW. But I did not want to risk that the battery "emptied" overnight.
Many greetings to Sweden.

Nachtrag vom 07.08.2017:
Ich habe wohl meinen Fehler gefunden. Ich bin ja der Annahme gewesen, dass das Entladen der Batterie evtl. von der Preview V0.0 käme. Aber nachdem der Husky auch mit der FW 0.9e jetzt am Wochenende keine Ladeaktivität mehr zeigte, habe ich ihn mir mal vorgeknöpft. Die LS gesäubert, alle Anschlusskabel entfernt und gereinigt, die Ladeschalen und -kontakte gesäubert und neu eingestellt, und alles wieder zusammengebaut. Und, er lädt und läuft wieder wie am ersten Tag. Angespornt von diesem Ergebnis, habe ich wieder die FW 0.0 vom 23.07.2017 installiert. Hat sofort auf Anhieb geklappt. Alles läuft bisher ohne Probleme. Die negativen Werte beim Laden sind bisher noch nicht wieder aufgetreten.
Inhaltlich hat sich ja einiges an der neuen FW verändert. Sieht toll aus. Fabian, vielen Dank für deine großartige Arbeit.

---

I have probably found my mistake. I am the assumption that the discharge of the battery possibly from the preview V0.0 came. But after the Husky also with the FW 0.9e now no longer show on weekends, I have him pre-button. The LS cleaned, all connection cables removed and cleaned, the charging baskets and contacts cleaned and re-adjusted, and everything reassembled. And, he loads and runs again as on the first day. Inspired by this result, I have again installed the FW 0.0 from 23.07.2017. It worked immediately. Everything runs so far without problems. The negative values ​​during loading have not yet occurred again.
In terms of content has changed a lot on the new FW. Looks great. Fabian, thank you for your great work.
Zuletzt geändert von Der RTler am Mo 7. Aug 2017, 12:14, insgesamt 1-mal geändert.
---
Bis denne ...

Gruß Werner

viahack
sehr erfahrener Forum-Nutzer
Beiträge: 208
Registriert: Di 26. Jul 2016, 16:08
Wohnort: Schönster Teil Deutschlands
Mäher: Gardena R40Li
Firmware des Mähers (MSW): MSW 2.xx.xx
Herstellungsjahr: 2011
Robonect-Modul: Robonect H30x (Rev.0)
Robonect Firmware: 1.0 beta 5
hat sich bedankt: 4 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von viahack »

Hi Malmgren,

I think it is a problem with updating.
At your charging station is only one spring for give electric contact.
So the mover must replace the second spring with logic.

At updating you set the AM in a big fault status(lose communication to the display).
At turn off the AM with the physical power button you make a cold start(reset of AM).

So my tip for updating.
Remove AM from charging station.
Press the stop button on AM.
Make Update.
....

Greeting
ViaHack /Jürgen
Automower: R40Li MSW-Version:2.01.00 MSW-Datum: 2011-09-05 17:32:18 SUB-Version: 2.00.00
Bootloader: V0.4 Kompiliert: 22.10.2016 01:12
W-LAN: AT-Version:V0.51.0 SDK-Version:V1.5.0
Hardware Seriennummer: 05DB0030-39394848-43115243

Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von Malmgren »

viahack hat geschrieben:
So 30. Jul 2017, 17:53
I think it is a problem with updating.
At your charging station is only one spring for give electric contact.
So the mover must replace the second spring with logic.
Ah, ok. So maybe it would have been enough just pulling the mower out of the station and putting it back in again?

/Daniel

JimKnopf
Forum-Nutzer
Beiträge: 41
Registriert: So 2. Apr 2017, 16:39
Wohnort: Leer (Ostfriesland)
Mäher: Gardena R38Li
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.3)
Robonect Firmware: V0.9e

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von JimKnopf »

Hi!
This is actually a preview.
Errorreports should not be send. If someone has troubble with one of the previews, reinstall the last stable version.
Fabian will tell us, when he want to get bugreports.

Regards, Burkhard
Lisa: R38li BJ2016, Main: 6.03.00 Sub: 6.00.00 HMI: 6.05.00 Robonect: Board:V3 2017-02. Firmware 0.9e. Fritzbox 6490 Cable (Kabel Deutschland)

Malmgren
Forum-Nutzer
Beiträge: 32
Registriert: Di 13. Jun 2017, 18:37
Wohnort: Sweden
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 6.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: 1.0 beta 7
wurde gedankt: 2 Male

Re: Battery not loading after upgrading to 1.0 preview

Beitrag von Malmgren »

JimKnopf hat geschrieben:
So 30. Jul 2017, 21:06
This is actually a preview.
Errorreports should not be send. If someone has troubble with one of the previews, reinstall the last stable version.
Fabian will tell us, when he want to get bugreports.
Oh, sorry. Thought he wanted feedback on the preview. Already sent him a mail about this. Guess he'll tell me the same thing then ;)

/Daniel

Gesperrt

Zurück zu „FW 1.0 Preview“