Das ist aber keine Lösung, eher eine Notlösung.bahnuhr hat geschrieben:Die Lösung heißt: Feste-ip.net
Und dann: Fip-Box
Damit funktioniert alles.
[CLOSED] IP V6 Adresse
-
- erfahrener Forum-Nutzer
- Beiträge: 55
- Registriert: Di 26. Jan 2016, 20:02
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.0)
- Robonect Firmware: 0.0
- wurde gedankt: 1 Mal
Re: IP V6 Adresse
AM 315 - Main 6.04.00 - SUB 6.00.00
-
- erfahrener Forum-Nutzer
- Beiträge: 55
- Registriert: Di 26. Jan 2016, 20:02
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.0)
- Robonect Firmware: 0.0
- wurde gedankt: 1 Mal
Re: IP V6 Adresse
Darf ich das noch einmal in Erinnerung rufen?grisu hat geschrieben: ↑Mo 3. Jul 2017, 12:00 Für alle die einen IPv6 Internetanschluß haben wäre die Möglichkeit dem Modul eine IPV6 Adresse zu geben enorm wichtig. Da man sonst leider nur mit einem zusätzlichen Gerät (Ipv6/ipv4 Mapper) die Möglichkeit hat von außen auf den Mäher zuzugreifen.
Es werden ja auch immer mehr Leute mit IPv6 Internetanschluß.
AM 315 - Main 6.04.00 - SUB 6.00.00
-
- erfahrener Forum-Nutzer
- Beiträge: 67
- Registriert: Di 25. Okt 2016, 18:42
- Wohnort: Denmark
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect H30x (Rev.3)
- Robonect Firmware: V1.3b
- wurde gedankt: 3 Male
-
- Administrator
- Beiträge: 2907
- Registriert: Di 19. Jan 2016, 18:34
- Wohnort: Kiel
- Mäher: Gardena SILENO City 500
- Firmware des Mähers (MSW): MSW 11.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: stets die Allerneuste :-)
- hat sich bedankt: 1 Mal
- wurde gedankt: 60 Male
- Kontaktdaten:
Re: IP V6 Adresse
Seit der V1.0 Beta 5 gibt es unter "Robonect > Fernzugriff" die Möglichkeit auch hinter einem IPv6 Anschluss auf Robonect zuzugreifen.
Werbefläche zu vermieten.
-
- erfahrener Forum-Nutzer
- Beiträge: 67
- Registriert: Di 25. Okt 2016, 18:42
- Wohnort: Denmark
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect H30x (Rev.3)
- Robonect Firmware: V1.3b
- wurde gedankt: 3 Male
IP v6 address
It would be good to be able to give the module an IPv6-address, so it can be accessed from outside without relying on 3rd party external servers.
230acx + 330x
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 120
- Registriert: Di 4. Apr 2017, 21:05
- Wohnort: Eichenzell
- Mäher: Husqvarna Automower 420
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: V1.2RC0
Re: IP V6 Adresse
19,80 Eur/Jahr stimmt.
Einen Raspi hat man doch noch rumliegen. Somit entfallen die 119,-EUR.
Und 19,80/Jahr damit ich per vpn auf alles zugreifen kann ist für mich ok.
mfg
-
- erfahrener Forum-Nutzer
- Beiträge: 76
- Registriert: Di 17. Apr 2018, 11:04
- Mäher: Gardena smart SILENO
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.3)
- Robonect Firmware: 1.0
Re: IP v6 address
+1 for that.
Even if some folks OUT there still think ipv6 is a not needed thing for some hardcore nerds it's needed. The ipv4 address pools are exhausted. If one opens a new isp and asks for ipv4 addresses at RIPE he will get a hand full addresses and most of the time from different subnets apart from that a big laugh.
A short look on the statistics here shows an adoption of almost 37% of the traffic.
So it's time to arrange with ipv6. Not sure which frameworks or libraries Fabian uses for the network stack, but all modern network stacks Support ipv6 so I hope ipv6 for RN is more a matter of testing and not a problem in the implementation as such.
bye
Sven
Even if some folks OUT there still think ipv6 is a not needed thing for some hardcore nerds it's needed. The ipv4 address pools are exhausted. If one opens a new isp and asks for ipv4 addresses at RIPE he will get a hand full addresses and most of the time from different subnets apart from that a big laugh.
A short look on the statistics here shows an adoption of almost 37% of the traffic.
So it's time to arrange with ipv6. Not sure which frameworks or libraries Fabian uses for the network stack, but all modern network stacks Support ipv6 so I hope ipv6 for RN is more a matter of testing and not a problem in the implementation as such.
bye
Sven
WLAN 3* Ubiquiti UAP-AC-Lite APs