Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

[V1.0 Beta 6]Charge larger battery

Funktionswünsche ab 2018 bis einschließlich Beta 7a
Falls Du in der aktuellen Firmware einen Wunsch hast, der bereits in Beta 7a formuliert wurde, schreibe bitte Deine Unterstützung dafür in einem Beitrag
-> dann wird dieses Thema ins aktuelle Wunsch-Forum verschoben! Versprochen!
larsan
sehr erfahrener Forum-Nutzer
Beiträge: 120
Registriert: So 26. Mär 2017, 11:31
Wohnort: Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.4
hat sich bedankt: 6 Male
wurde gedankt: 20 Male
Kontaktdaten:

[V1.0 Beta 6]Charge larger battery

Beitrag von larsan »

Hi!

I'd like the ability to trick my mower into fully charging a 2500mAh battery.
As it is now, it's only charged to about 1200mAh.
Best regards,
David from Sweden

duese51
erfahrener Forum-Nutzer
Beiträge: 54
Registriert: Do 14. Apr 2016, 12:12

Re: Charge larger battery

Beitrag von duese51 »

Hi Iarsan,

you don't need a trick to full Charge your battery. Bu you need a trick to empty the battery complete (see below)

a - During charging the batterie voltage is being measured. Charging is stopped when the charge end voltage ist reached (about 21V)

b -The battery capacitiy then is explizitely set to 1200mAh.

c - In mode auto now the consumption of mAh is measured an integrated over time and then substracted from 1200mAh.

d - When the batterie capacity reaches 300 mAh the mover goes home for recharging.

To take advantage from your higher capacitiy you can do the following steps (without leaving your home):

1. Start the mower in mode auto
2. When the mower begins mowing switch it over to manuell.
3. When the battery voltage reaches 17.5V Switch it over to home

Now your battery is empty but has still enough capacity for the mower to go home.
17.5 V is a conservative discharge voltage to prevent damage to your battery .
If you forget to set the mower to home (3.) nevertheless the mower will stop at a lower discharge voltage than 17.5 V.

I use FHEM in kombination with the api do that all automatically. My Husqvarna 305 now mowes for more than 2 hours before recharge is necessary

Kind regards

Bernd
Husqvarna

MSW-Software: 305
MSW-Version: 3.02.00
MSW-Datum: 2012-10-18 07:37:23
SUB-Version: 3.00.00

Robonect SW 1.1b

larsan
sehr erfahrener Forum-Nutzer
Beiträge: 120
Registriert: So 26. Mär 2017, 11:31
Wohnort: Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.4
hat sich bedankt: 6 Male
wurde gedankt: 20 Male
Kontaktdaten:

Re: Charge larger battery

Beitrag von larsan »

Thank you Bernd.

May I ask which battery you are using?
Also, how often does one need to do that auto/manual/home-procedure?
Best regards,
David from Sweden

top_gun_de
sehr erfahrener Forum-Nutzer
Beiträge: 277
Registriert: Mo 15. Aug 2016, 00:01
Mäher: Gardena smart SILENO+
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: 1.0 beta 6
wurde gedankt: 1 Mal

Re: Charge larger battery

Beitrag von top_gun_de »

If your question is inspired by battery maintenance, then the answer is: Not at all.

A lithium battery is completely different from a NiMh-battery. It lasts best if it is only used with a shallow carging-profile: Never fully deplete, and never fully charge the battery. The voltages in the firmware are designed not to reach either the full- nor the empty-state, this way the battery lasts longer than when it is fully cycled.

You should only use the described trick if your time-window for mowing needs longer drives.

Best,

Detlev

larsan
sehr erfahrener Forum-Nutzer
Beiträge: 120
Registriert: So 26. Mär 2017, 11:31
Wohnort: Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.4
hat sich bedankt: 6 Male
wurde gedankt: 20 Male
Kontaktdaten:

Re: Charge larger battery

Beitrag von larsan »

It is inspired by battery maintenance, and run time.
My idea was to use a 2500mAh battery instead of a 1600mAh one, to prolong run time, and decrease the number of charges needed per day.
Best regards,
David from Sweden

duese51
erfahrener Forum-Nutzer
Beiträge: 54
Registriert: Do 14. Apr 2016, 12:12

Re: Charge larger battery

Beitrag von duese51 »

Hi Larsan,
you have to do that procedure which I described anytime you start the mower.

The only advantage of the procedure i described is, that you can do it from your living room and have not to go outside, by only using the the start in manuell mode.

That is the reason for my recommendation to do that automatically. The only way I see is to do that by FHEM unless admin integrates my proposal as a new mode into his SW.
The HX module has all information to to that already available. The procedure - I name it "extended" - is trivial. Perhaps you should make a feature request for that.

@top-gun
Using my procedure :
a
The full Status of the battery is furthermore managed by the firmware of the Roboter.

b The empty Status of the battery will be recognized by the firmware of the Roboter at a Level which ist lower then the 17.5V I propose. Thus care for the battery is furthermore guaranteed.

Kind regards

bernd
Husqvarna

MSW-Software: 305
MSW-Version: 3.02.00
MSW-Datum: 2012-10-18 07:37:23
SUB-Version: 3.00.00

Robonect SW 1.1b

Benutzeravatar
johan63
Forum-Nutzer
Beiträge: 42
Registriert: Di 7. Jun 2016, 12:18
Wohnort: Strömsnäsbruk,Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.3 28.06.2021 (Final Release)Kamera
hat sich bedankt: 2 Male
wurde gedankt: 1 Mal
Kontaktdaten:

Re: Charge larger battery

Beitrag von johan63 »

duese51 hat geschrieben:
So 23. Apr 2017, 17:28
Hi Iarsan,

you don't need a trick to full Charge your battery. Bu you need a trick to empty the battery complete (see below)

a - During charging the batterie voltage is being measured. Charging is stopped when the charge end voltage ist reached (about 21V)

b -The battery capacitiy then is explizitely set to 1200mAh.

c - In mode auto now the consumption of mAh is measured an integrated over time and then substracted from 1200mAh.

d - When the batterie capacity reaches 300 mAh the mover goes home for recharging.

To take advantage from your higher capacitiy you can do the following steps (without leaving your home):

1. Start the mower in mode auto
2. When the mower begins mowing switch it over to manuell.
3. When the battery voltage reaches 17.5V Switch it over to home

Now your battery is empty but has still enough capacity for the mower to go home.
17.5 V is a conservative discharge voltage to prevent damage to your battery .
If you forget to set the mower to home (3.) nevertheless the mower will stop at a lower discharge voltage than 17.5 V.

I use FHEM in kombination with the api do that all automatically. My Husqvarna 305 now mowes for more than 2 hours before recharge is necessary

Kind regards

Bernd
How do you do this automatically with the API? Do you have a howto?
Gardena Sileno smart 750. V1.3 28.06.2021 (Final Release)+ Kamera FB: Tommy Cederlund "SWEDEN"

Admin
Administrator
Beiträge: 2903
Registriert: Di 19. Jan 2016, 18:34
Wohnort: Kiel
Mäher: Gardena SILENO City 500
Firmware des Mähers (MSW): MSW 11.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: stets die Allerneuste :-)
hat sich bedankt: 1 Mal
wurde gedankt: 59 Male
Kontaktdaten:

Re: Charge larger battery

Beitrag von Admin »

I will implement the method of duese51 directly into the Robonect Firmware, if he has no copyrights on it. ;)
Werbefläche zu vermieten. :lol:

Benutzeravatar
johan63
Forum-Nutzer
Beiträge: 42
Registriert: Di 7. Jun 2016, 12:18
Wohnort: Strömsnäsbruk,Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.3 28.06.2021 (Final Release)Kamera
hat sich bedankt: 2 Male
wurde gedankt: 1 Mal
Kontaktdaten:

Re: Charge larger battery

Beitrag von johan63 »

Admin hat geschrieben:
So 30. Apr 2017, 18:10
I will implement the method of duese51 directly into the Robonect Firmware, if he has no copyrights on it. ;)
It sounds brilliant, a little hard to constantly change from auto to manual and then to auto again before mower is going home. If you click on the auto just before the mover goes home, the times come up in robonect.
Gardena Sileno smart 750. V1.3 28.06.2021 (Final Release)+ Kamera FB: Tommy Cederlund "SWEDEN"

larsan
sehr erfahrener Forum-Nutzer
Beiträge: 120
Registriert: So 26. Mär 2017, 11:31
Wohnort: Sweden
Mäher: Gardena smart SILENO
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.4
hat sich bedankt: 6 Male
wurde gedankt: 20 Male
Kontaktdaten:

Re: Charge larger battery

Beitrag von larsan »

johan63 hat geschrieben:
So 30. Apr 2017, 20:19
Admin hat geschrieben:
So 30. Apr 2017, 18:10
I will implement the method of duese51 directly into the Robonect Firmware, if he has no copyrights on it. ;)
It sounds brilliant, a little hard to constantly change from auto to manual and then to auto again before mower is going home. If you click on the auto just before the mover goes home, the times come up in robonect.
That would indeed be awesome. What's the time frame for that? If it's too long, I'll whip up a script to poll and change statuses accordingly.
Best regards,
David from Sweden

Gesperrt

Zurück zu „Wünsche bis Beta 7a“