My Automower 420 refuses to mow complaining about errorcode 19 "rear bump sensor defect"
Which sensor is that? Aren't bump sensors joysticks on each side left and right? If so then ehoch one of two is has problems?
Is it possible to fix it by cleaning contacts for example or not?
Die Suche ergab 39 Treffer
- Mo 27. Jun 2022, 23:06
- Forum: allgemeine Mäher-Frage?
- Thema: Rear bump sensor defect [SOLVED]
- Antworten: 1
- Zugriffe: 229
- So 13. Jun 2021, 07:38
- Forum: Kamera einbauen
- Thema: ESP32Cam Stromdieb - (Zubehör)
- Antworten: 4
- Zugriffe: 1875
Re: ESP32Cam Stromdieb - (Zubehör)
Hi
I wonder if anyone of managed to get going with esp32cam. I have also two modules lying around and I'm thinking to hook it up. The only drawback i see with is extra wifi interference. If using pct camera then you only get one wifi transmitter on the mower.
I wonder if anyone of managed to get going with esp32cam. I have also two modules lying around and I'm thinking to hook it up. The only drawback i see with is extra wifi interference. If using pct camera then you only get one wifi transmitter on the mower.
- So 9. Aug 2020, 17:50
- Forum: Mähzeit oder Lebensdauer des Akku erhöhen
- Thema: What to config?
- Antworten: 3
- Zugriffe: 1377
Re: What to config?
Thanks for the replies. Yes indeed that's the case. I have tested it by switching the extend mowi g time using mowing time adjustment. Moreover the timer function for some reason was not working, maybe due to other issue I found, so the mower was mowing 24/7.
- So 9. Aug 2020, 08:15
- Forum: allgemeine Mäher-Frage?
- Thema: Timer not being taken into consideration [SOLVED]
- Antworten: 2
- Zugriffe: 514
Re: Timer not being taken into consideration
Thanks. That helped
- So 9. Aug 2020, 05:04
- Forum: allgemeine Mäher-Frage?
- Thema: Timer not being taken into consideration [SOLVED]
- Antworten: 2
- Zugriffe: 514
Timer not being taken into consideration [SOLVED]
Hi
My mower seems to not care about a timer setting and instead mowing 24/7. I have only one timer active which is timer1 and that is set from 6-22. Look at the screenshots. But still it mowes all the time. Is there another setting that is overriding it?
My mower seems to not care about a timer setting and instead mowing 24/7. I have only one timer active which is timer1 and that is set from 6-22. Look at the screenshots. But still it mowes all the time. Is there another setting that is overriding it?
- Di 4. Aug 2020, 09:09
- Forum: Mähzeit oder Lebensdauer des Akku erhöhen
- Thema: BMS in Husqvarna batteries
- Antworten: 33
- Zugriffe: 8230
Re: BMS in Husqvarna batteries
Hi
I am back to countryside and was measured the control resistor of my original pack which is 18v/3.2Ah. The resistor is a tiny one inside a heat shrink tube. It measures 12K precisely. It tested with two different multimeters just for fun.
I hope this helps.
I am back to countryside and was measured the control resistor of my original pack which is 18v/3.2Ah. The resistor is a tiny one inside a heat shrink tube. It measures 12K precisely. It tested with two different multimeters just for fun.
I hope this helps.
- So 2. Aug 2020, 17:15
- Forum: Gemischtes und Kurioses
- Thema: Drawing power from robonect card
- Antworten: 5
- Zugriffe: 2413
Re: Drawing power from robonect card
Pi has to be On all the time since it can go into sleep when for example it is stuck in rhe garden due to e.g. "no traction". I want to see where it is to joystick control it and restart. For that I need gps position as well as camera view. Anyway. It would be a better solution to connect ...
- So 2. Aug 2020, 06:33
- Forum: Gemischtes und Kurioses
- Thema: Drawing power from robonect card
- Antworten: 5
- Zugriffe: 2413
Re: Drawing power from robonect card
Well since I could only find 3v3 output on robonect board I though I would usr it. It is possible to power pi zero with 3.3v for low power applications. I am using it today for my own gps tracker solution. I would like to draw 5v of course but I couldn't find a way to get from robonect or from mower...
- Do 30. Jul 2020, 15:00
- Forum: Gemischtes und Kurioses
- Thema: Drawing power from robonect card
- Antworten: 5
- Zugriffe: 2413
Drawing power from robonect card
Hi I need to power my Pi Zero and I can see and even confirmed by measuring that robonect has 3.3V output on it's board. See the pic. Power was present on +3V3 output 7 on the board and I was also been able to get it via the OUT pins when enabled in the menu. Can anyone tell me how much power can I ...
- Di 14. Jul 2020, 13:59
- Forum: kein Bug
- Thema: Mowing times not being updated
- Antworten: 1
- Zugriffe: 1702
Mowing times not being updated
Hi It looks like the Operational Hours->Mowing times not being updated when running in "Mowing time adjustment:->Extend Mowing Time". On the other hand Seek times are being updated. Is anyone seen this or confirmed earlier? I can send more data/debug if needed/instructed. xxxx1.JPG Here ar...