Hi everybody
I update the fw module to 1.0beta8, it's ok for that. But i can't find links for the two orther files..
Thanks
Where is Part 2 and 3 of the Update? [CLEARED]
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 11. Jan 2017, 18:34
- Wohnort: Cherbourg en France
- Mäher: Husqvarna Automower 105
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7a
Where is Part 2 and 3 of the Update? [CLEARED]
Husqvarna AM105 (Modèle 2016) MSW 6.14.00, SUB-Version 6.01.00
Robonect HX rev 5, firmware 0.9e
Robonect HX rev 5, firmware 0.9e
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Where is Part 2 and 3 of the Update?
The other files need to become more comfortable for users not accepting/reading/translating the rules standing before the download links....
So Fabian will post them later this days again. You can use Beta 8 either. But you have to wait for some days to get the full bugfixes and features you can get then with Part 2 (ZeroConf) und Part 3 (WiFi) update files.
So Fabian will post them later this days again. You can use Beta 8 either. But you have to wait for some days to get the full bugfixes and features you can get then with Part 2 (ZeroConf) und Part 3 (WiFi) update files.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- Forum-Nutzer
- Beiträge: 20
- Registriert: Mi 11. Jan 2017, 18:34
- Wohnort: Cherbourg en France
- Mäher: Husqvarna Automower 105
- Firmware des Mähers (MSW): MSW 6.xx.xx
- Herstellungsjahr: 2016
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: 1.0 beta 7a
Re: Where is Part 2 and 3 of the Update?
Yes, sorry for this message
Husqvarna AM105 (Modèle 2016) MSW 6.14.00, SUB-Version 6.01.00
Robonect HX rev 5, firmware 0.9e
Robonect HX rev 5, firmware 0.9e