Installation guide for Husqvarna Automower 420 (in English)

Anleitungen und Einbauvorschläge für das Hx-Modul in verschiedene Mäher-Modelle
Antworten
bortek
Forum-Nutzer
Beiträge: 37
Registriert: Mi 18. Jul 2018, 19:30
Mäher: Husqvarna Automower 420
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2017
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.0
wurde gedankt: 1 Mal

Installation guide for Husqvarna Automower 420 (in English)

Beitrag von bortek »

Installation of the module is fairly simple and takes about 15 minutes. Power off your robot before you continue.

Anmerkung der Moderation-Beginn
:!: Wichtig!
  1. Hauptschalter am Mäher ausmachen (switch off power switch first)
  2. Mäher öffnen, wie beschrieben (open the mower like shown in this guide)
  3. :arrow: Stromkabel des Akku von der Hauptplatine des Mähers abziehen!
    :arrow: Before installing Rebonect the power cable has to be detached off the mowers mainboard first!
  4. weiter wie in der Anleitung verfahren (keep on beeing explained in this guide)
Anmerkung der Moderation-Ende

file2.jpg
First of all you need to remove top cover form the robot. Before you do it you need to disconnect the charging cable. Just pull off the rubber spacer and disconnect the cable.


file3.jpg
Then put one hand on the dashboard and with another one pull up the front side and then same for the back side of the top cover.


file4.jpg
Now you are ready to start unscrewing the robot chassi. Clean it with a brush or dry cloth to avoid dust/grass/etc coming inside the unit during next steps.


file6.jpg
There are 14 screws you need to remove located on the perimeter of the chassi.


file7.jpg
Say goodbye to you warranty and tear off the label.


file8.jpg
Gently lift the cover of the chassi.


file9.jpg
This is how it looks inside. Plenty of space to place the module.


file10.jpg
file11.jpg
Now detach this cable (which comes from the display) from the robots main board by pressing two clips as shown.


file12.jpg
Attach Robonect modules cable to the robots main (where you just detached the cable from in the previous step)


file13.jpg
file14.jpg
Attach robots display cable (which you unplugged in previous steps) to the Robonect module.


file15.jpg
file16.jpg
Now you need to place the module inside and stick it using adhesive pads that came with the module. I placed it to the right of the center motor. You can place it to the left too. Just make sure you place it no too close to power wires to minimize interference.


file17.jpg
Put back the cover and secure it with 14 screws.


file1.jpg
Put back the top cover and press until it clicks ont he "joysticks". Connect back the charging cable and push the grommet inside.

Power up your robot. Find the Wifi called Robonect or alike and connect to it. It is easier to do it from the PC , not from you mobile. Surf into to http://192.168.2.1. Select language and proceed.
Now you need to install the firmware. Download it from https://www.robonect-shop.de/downloads/

In the web gui find where to upload your firmware file and point to the file you just downloaded. All other config is self-explanatory and easy.


Have fun! :)
Zuletzt geändert von shadowkiller am Do 3. Sep 2020, 19:45, insgesamt 1-mal geändert.
Grund: Anmerkung der Moderation eingefügt
Folgende Benutzer bedankten sich beim Autor bortek für den Beitrag:
shadowkiller
Bewertung: 50%

Benutzeravatar
saugbaer
Forum-Veteran
Beiträge: 1371
Registriert: Mo 18. Apr 2016, 01:30
Wohnort: Ramelsloh
Mäher: Husqvarna Automower 310
Firmware des Mähers (MSW): MSW 7.xx.xx
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: V1.2 08.10.2020 17:06
hat sich bedankt: 1 Mal
wurde gedankt: 3 Male

Re: Installation guide for Husqvarna Automower 420 (in English)

Beitrag von saugbaer »

Bigthx For the work
:mrgreen: Ich bin nicht die Signatur, ich putz hier nur :mrgreen:
AVM 7490 Fw.7.12 + 2AP's (FRITZ!Powerline 546E + FRITZ!WLAN Repeater 1160 Fw.7.12)
HX + APP + VPN + Kamera + LED

Antworten

Zurück zu „Einbau-Anleitungen“