Hello,
My robot is making annoying "biiiiiip" sounds in several cases (when manually stopped, when accessing keyboard, every day at midnight ...).
Could we have a parameter to Stop these sounds ?
I would like to keep all sounds related to alarms though.
It would be good if we could choose accurately the sounds we want.
Thank you.
Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
. Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
. Testmöglichkeit für das Daily Build.
Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!
.
.
Sound off
- shadowkiller
- Forum-Veteran
- Beiträge: 4467
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 159 Male
- wurde gedankt: 132 Male
Re: Sound off
Be welcome!
The sound is initiated by the mowers logic board. Robonect has no possibility to get any control over this.
The two short beeps result on awaking the mower because
- you get access through the mowers keybord for getting infos, for loading the data for this case.
- you get access through Robonect for getting infos like "Fault-Memory", for loading the data for this case.
- "you" get access through a smart home control system, for loading the data for this case.
You can switch it off completely by unplugging the speakers connector. But then there will be no sounds in case of alarms.
You can also minimize the the sounds by controlling accesses through your smart home system (making them less).
The sound control is like "mowing while controlling by Joystick": not possible to control by robonect. Sorry.
The sound is initiated by the mowers logic board. Robonect has no possibility to get any control over this.
The two short beeps result on awaking the mower because
- you get access through the mowers keybord for getting infos, for loading the data for this case.
- you get access through Robonect for getting infos like "Fault-Memory", for loading the data for this case.
- "you" get access through a smart home control system, for loading the data for this case.
You can switch it off completely by unplugging the speakers connector. But then there will be no sounds in case of alarms.
You can also minimize the the sounds by controlling accesses through your smart home system (making them less).
The sound control is like "mowing while controlling by Joystick": not possible to control by robonect. Sorry.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)