Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

Weather Unavailable (Error 500)

- alle Auffälligkeiten die es zu klären gilt
- Verdacht, dass ein echter Bug vorliegt

:!: Bevor Du Deinen Bug-Verdacht meldest, wurde er vielleicht schon behoben!

Hast Du das aktuelle Daily Bulid schon ausprobiert? Vielleicht ist Dein Bug ja schon gefixt!? :arrow: Download

Falls das Daily Build Dein Problem nicht lösen konnte, schreibe bitte das Datum aus Deinem installierten Daily Built (schwarze Fußzeile im Robonect-Menü) in Deinen Bug-Bericht dazu! Viel Spaß beim Testen!
bchabrier
Forum-Anfänger
Beiträge: 8
Registriert: So 20. Dez 2020, 00:20
Mäher: Gardena SILENO City 250
Firmware des Mähers (MSW): MSW 6.xx.xx
Robonect Firmware: V1.2 (Fix)

Weather Unavailable (Error 500)

Beitrag von bchabrier »

Hello,

I have a problem with the weather Service which fails after a while. It starts fine, but after some time, I get an Error 500.

It seems that I have this problem since I moved to V1.2. I upgraded to V1.2(Fix) (Robonect Hx+ V1.2 (10.10.2020 23:13)) but still have the same behaviour.

When I restart Robonect, the weather Service works fine again and correctly displays weather information in the Robonect UI, but will fail some time after and display Error 500 .

I have tried to make some measurement and it seems that the delay until it fails is between 6 hours and 6 hours and 30 minutes. Also, once Error 500 is raised, it stays forever.

Any idea what happens and how to fix it?

Regards,
Bruno

Benutzeravatar
SenfmitHonig
sehr erfahrener Forum-Nutzer
Beiträge: 457
Registriert: So 30. Okt 2016, 22:39
Wohnort: 943xx
Mäher: Husqvarna Automower 430X
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: V1.3
hat sich bedankt: 4 Male
wurde gedankt: 34 Male

Re: Weather Unavailable (Error 500)

Beitrag von SenfmitHonig »

Servus Bruno,
when Robonect can not connect to the Internet, this error message appears!
Do your network settings match?
Do you come via the remote access mower.online at the error time on the mower?

bchabrier
Forum-Anfänger
Beiträge: 8
Registriert: So 20. Dez 2020, 00:20
Mäher: Gardena SILENO City 250
Firmware des Mähers (MSW): MSW 6.xx.xx
Robonect Firmware: V1.2 (Fix)

Re: Weather Unavailable (Error 500)

Beitrag von bchabrier »

Hi, thanks for your reply.

My internet settings seems OK, as I can get the weather information as soon as I restart Robonect:
restarted.png
And after a couple of hours (a bit more than 6 hours), I get the error again:
error.png
I can imagine that sometimes, the internet connection could fail and generate error 500, but in that case, why would it stay on error and not reconnect when the internet connection is back? Also, I never experienced this behaviour before V1.2...

Very strange and annoying...

Benutzeravatar
SenfmitHonig
sehr erfahrener Forum-Nutzer
Beiträge: 457
Registriert: So 30. Okt 2016, 22:39
Wohnort: 943xx
Mäher: Husqvarna Automower 430X
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: V1.3
hat sich bedankt: 4 Male
wurde gedankt: 34 Male

Re: Weather Unavailable (Error 500)

Beitrag von SenfmitHonig »

Servus Bruno,
take a Screenshot of the network settings (acess point and home network)?
If also here no error is to be found maybe Fabian can help ...

bchabrier
Forum-Anfänger
Beiträge: 8
Registriert: So 20. Dez 2020, 00:20
Mäher: Gardena SILENO City 250
Firmware des Mähers (MSW): MSW 6.xx.xx
Robonect Firmware: V1.2 (Fix)

Re: Weather Unavailable (Error 500)

Beitrag von bchabrier »

Hi again, and thanks for your prompt reply. It is very appreciated to see my questions being addressed :)

Here you can find my AP configuration:
AP.png
And my LAN configuration:
LAN.png
Note than my local IP addressed is fixed, provided by my box DHCP server, configured to use 192.168.0.16 based on the MAC address.

Kind regards and frohe Weihnacht!
Bruno

Benutzeravatar
SenfmitHonig
sehr erfahrener Forum-Nutzer
Beiträge: 457
Registriert: So 30. Okt 2016, 22:39
Wohnort: 943xx
Mäher: Husqvarna Automower 430X
Herstellungsjahr: 2016
Robonect-Modul: Robonect Hx (Rev.2)
Robonect Firmware: V1.3
hat sich bedankt: 4 Male
wurde gedankt: 34 Male

Re: Weather Unavailable (Error 500)

Beitrag von SenfmitHonig »

Servus Bruno,
can you answer this question for me?
Do you come via the remote access https://xxx.mower.online at the error time on the mower?
This could be used to check if the problem is with Robonect's Internet access. :problem:

The network settings should fit in my opinion!
I can not understand the 6 hours ... (is it possible that this is due to the setting in the OWM?)

if you have remote access at the Error-Time, then send Fabian (Admin) a PN with log and the reference to this page, possibly he can see the error.

bchabrier
Forum-Anfänger
Beiträge: 8
Registriert: So 20. Dez 2020, 00:20
Mäher: Gardena SILENO City 250
Firmware des Mähers (MSW): MSW 6.xx.xx
Robonect Firmware: V1.2 (Fix)

Re: Weather Unavailable (Error 500)

Beitrag von bchabrier »

Hi!

Thanks again for your reply.
Do you come via the remote access https://xxx.mower.online at the error time on the mower?
=> No, I'm not using the internet access, my mower is only accessible through the LAN.

I can get the log, so will send this to Fabian and hopefully he will figure OUT what is happening...

Thanks for your great Support!

Benutzeravatar
shadowkiller
Forum-Veteran
Beiträge: 4467
Registriert: Do 11. Jan 2018, 08:42
Wohnort: Würzburg
Mäher: Husqvarna Automower 315
Firmware des Mähers (MSW): MSW 10.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.3 (WLAN 1.7.4)
hat sich bedankt: 159 Male
wurde gedankt: 132 Male

Weather Unavailable (Error 500)

Beitrag von shadowkiller »

Without internet access the weather feature will not work....

Your home network has no access to the internet.? Can’t believe it. Isn’t it connected to your router?

And LAN is not, what you mean because this would be via network cable only. What you mean is Wireless LAN, I think.

Look in your routers config. Maybe you’ve block internet traffic to some times a day or for robonects internal IP? Maybe it’ll help to reset the network configuration for Robonect in your router and add it from ground up new in your router. In Robonect itself there is nothing you have to do for this.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)

bchabrier
Forum-Anfänger
Beiträge: 8
Registriert: So 20. Dez 2020, 00:20
Mäher: Gardena SILENO City 250
Firmware des Mähers (MSW): MSW 6.xx.xx
Robonect Firmware: V1.2 (Fix)

Re: Weather Unavailable (Error 500)

Beitrag von bchabrier »

Sorry, my previous message was misleading. What I meant is that I am accessing my mower (hence the Robonect) only through my local area network (LAN), through Wifi. I did not activate the remote access to the Robonect (i.e. from the internet), so I do not use the xxx.mmower.online access.

Does this clarify?

Benutzeravatar
shadowkiller
Forum-Veteran
Beiträge: 4467
Registriert: Do 11. Jan 2018, 08:42
Wohnort: Würzburg
Mäher: Husqvarna Automower 315
Firmware des Mähers (MSW): MSW 10.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.3 (WLAN 1.7.4)
hat sich bedankt: 159 Male
wurde gedankt: 132 Male

Weather Unavailable (Error 500)

Beitrag von shadowkiller »

Yes. But why not activating remote access just for finding OUT what’s going on? Therese no risk at all.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)

Antworten

Zurück zu „Bug?“