Hi,
Today I installed the Multifunktionsrelais.
Everything is working fine, the only problem is that I always get the error mail:
Passage module malfunction!
The Passage could not be opened / closed! Check the connection and settings!
But the Relay open and close as expected.
The notification 'In case of malfunction of the Passage module:' is checked in my notifications settings.
Ofcource, I can uncheck it, but than I don't get a message if it is really failing.
Also to robot is stopped then when 'Abort mowing operation if error occurs' is checked in the Passage settings. So I already unchecked it, otherwise the mower is stopping every time it want to open/close the Passage.
Passage module malfunction notification
Forumsregeln
Bevor Du Deinen Bug-Verdacht meldest, wurde er vielleicht schon behoben!
Hast Du das aktuelle Daily Bulid schon ausprobiert? Vielleicht ist Dein Bug ja schon gefixt!? Download
Falls das Daily Build Dein Problem nicht lösen konnte, schreibe bitte das Datum aus Deinem installierten Daily Built (schwarze Fußzeile im Robonect-Menü) in Deinen Bug-Bericht dazu! Viel Spaß beim Testen!
Bevor Du Deinen Bug-Verdacht meldest, wurde er vielleicht schon behoben!
Hast Du das aktuelle Daily Bulid schon ausprobiert? Vielleicht ist Dein Bug ja schon gefixt!? Download
Falls das Daily Build Dein Problem nicht lösen konnte, schreibe bitte das Datum aus Deinem installierten Daily Built (schwarze Fußzeile im Robonect-Menü) in Deinen Bug-Bericht dazu! Viel Spaß beim Testen!
-
- Forum-Nutzer
- Beiträge: 10
- Registriert: Do 16. Sep 2021, 18:49
- Mäher: Husqvarna Automower 305
- Robonect Firmware: -
Re: Passage module malfunction notification
Hi,
I have to say that this is not happen always. But 3 a 4 times per week.
For the rest, I like Robonect very much
Also the pushover and other options are very nice.
I have to say that this is not happen always. But 3 a 4 times per week.
For the rest, I like Robonect very much
Also the pushover and other options are very nice.
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 706
- Registriert: Di 14. Feb 2017, 17:07
- Mäher: Husqvarna Automower 330X
- Firmware des Mähers (MSW): MSW 7.xx.xx
- Herstellungsjahr: 2014
- Robonect-Modul: Robonect Hx (Rev.1)
- Robonect Firmware: V1.3b
- hat sich bedankt: 8 Male
- wurde gedankt: 82 Male
Re: Passage module malfunction notification
Hello MarcV,
from your description, I suspect that the reception conditions are not sufficient everywhere in the garden. It could also be related to a change in the AP while sending the command to open or close the gate.
greeting
Lampi
from your description, I suspect that the reception conditions are not sufficient everywhere in the garden. It could also be related to a change in the AP while sending the command to open or close the gate.
greeting
Lampi
Fragen? Fragen!
-
- Forum-Nutzer
- Beiträge: 10
- Registriert: Do 16. Sep 2021, 18:49
- Mäher: Husqvarna Automower 305
- Robonect Firmware: -
Re: Passage module malfunction notification
I think I know the problem.
I power the Relay with a solar powerbank. Sometimes I can't reach the Relay also not via IP via the network.
After measuring the voltage on the Relay, I sow that it was not 5V , even when the powerbank was fully charged.
After disconnecting, an reconnection again, it was OK again.
I think the powerbank needs a minimum of current to charge something,
I power the Relay with a solar powerbank. Sometimes I can't reach the Relay also not via IP via the network.
After measuring the voltage on the Relay, I sow that it was not 5V , even when the powerbank was fully charged.
After disconnecting, an reconnection again, it was OK again.
I think the powerbank needs a minimum of current to charge something,
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 159
- Registriert: Mo 30. Okt 2017, 07:22
- Wohnort: Bergisches Land
- Mäher: Gardena SILENO Life SMART
- Robonect-Modul: noch kein Robonect verbaut
- hat sich bedankt: 1 Mal
- wurde gedankt: 7 Male
Re: Passage module malfunction notification
Most power banks switch off after a while because the Relay pulls too little.
Gardena Sileno life 750 smart | Robonect SW: V1.3 Release | Robonect: Hx+ Hardware V10