Aufgrund derzeit hohem Spamaufkommens werden neue Nutzer sehr restriktiv behandelt. Nach kurzer "Bewährungszeit" hat man als normaler Nutzer weitreichende Rechte und benötigt auch kein Captcha mehr.
.
Nutzer, die sich danach dennoch als Spammer oder Trolle erweisen, können jederzeit wieder auf diesen Status zurückgesetzt oder gebannt werden.
Dasselbe gilt für Versuche, politische Überzeugungen kund zu tun, egal aus welcher Richtung diese kommen.
.
.:!: Achtung! Derzeit ist Robonect (noch) nicht mit dem Automower 305 ab Baujahr 2020 zusammen mit der neuen Mäher-FW MSW 41.4.0 kompatibel!
Aber: Im DailyBuild ist ein Patch enthalten, der getestet werden kann! (Stand 15.02.2024)
.
.Du hast Deinen Gardena-Mäher auf die Gardena-Firmware von 2023 aktualisiert?
.:arrow: Testmöglichkeit für das Daily Build.

Das FW-Update am Mäher wird dennoch nicht empfohlen, da das Daily Build nach aktuellen Berichten von Beta-Testern noch keine vollständige Kompatibilität gewährleisten kann! (Stand: 15.02.2024)
Wir empfehlen, das Gardena-Update noch nicht durchzuführen!

.
.

SW7a-Return to base via boundary line problem [POSSIBLE BUG, UNRESOLVED]

- alle Auffälligkeiten, die es zu klären gilt
- Verdacht, dass ein echter Bug vorliegt
Gesperrt
Toomaster
Forum-Anfänger
Beiträge: 3
Registriert: Mi 28. Jun 2017, 09:09
Mäher: Husqvarna Automower 315
Herstellungsjahr: 2015
Robonect-Modul: Robonect Hx (Rev.4)
Robonect Firmware: beta 7a

SW7a-Return to base via boundary line problem [POSSIBLE BUG, UNRESOLVED]

Beitrag von Toomaster »

Hi, sorry for typing in english.

I have automower 315 (2015) and FW Beta 7a.

I discovered that return to base via boundary line ONLY works if both settings are active and have the same value (boundary: return to base-right, return to base-left).
Meaning that the mower don´t follow the boundary line to the base station if the value is´t equal, or if only one option is checked (active).
Zuletzt geändert von shadowkiller am So 23. Jun 2019, 16:58, insgesamt 2-mal geändert.
Grund: Titel vorläufig an aktuellen Status angepasst

Admin
Administrator
Beiträge: 2903
Registriert: Di 19. Jan 2016, 18:34
Wohnort: Kiel
Mäher: Gardena SILENO City 500
Firmware des Mähers (MSW): MSW 11.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: stets die Allerneuste :-)
hat sich bedankt: 1 Mal
wurde gedankt: 59 Male
Kontaktdaten:

[ZU BESTÄGTIGEN] SW7a-Return to base via boundary line problem

Beitrag von Admin »

Can someone with a Automower 315 confirm this?
If so, i will combine left and right boundary.
Werbefläche zu vermieten. :lol:

Benutzeravatar
shadowkiller
Forum-Veteran
Beiträge: 4467
Registriert: Do 11. Jan 2018, 08:42
Wohnort: Würzburg
Mäher: Husqvarna Automower 315
Firmware des Mähers (MSW): MSW 10.xx.xx
Herstellungsjahr: 2017 (Modell 2018)
Robonect-Modul: Robonect Hx (Rev.5)
Robonect Firmware: 1.3 (WLAN 1.7.4)
hat sich bedankt: 159 Male
wurde gedankt: 132 Male

Re: SW7a-Return to base via boundary line problem

Beitrag von shadowkiller »

I’ll test it today... please standby ;)
O.k. tested!
Toomaster hat geschrieben:
Do 11. Apr 2019, 14:01
I discovered that return to base via boundary line ONLY works if both settings are active and have the same value (boundary: return to base-right, return to base-left).
Meaning that the mower don´t follow the boundary line to the base station if the value is´t equal, or if only one option is checked (active).
I can confirm this. The only way to make it work, is to have both active. Having only one side active in robonect it results in endless searching without moving along the boundary wires but crossing them like in mowing mode. The reverse test draws the same picture: if test right or left is started in the mowers display it results in both sides activated in robonect, however I deactived both in Robonect and saved this settings.

The users manual describes the following and is confirming this, too: boundary wire activated for finding the charging station the mower randomly decides which direction it will follow right or left side along the boundary wire. So ist doesn't matter for Robonect settings: only one checkbox for the boundary wire itself is needed.

Notice: following the boundary wire worked for me, but docking in the charging station only worked having the stations radio signal on, too. Without this, the mower just ignored its existence (maybe because my station is not located on the lawn like Husqvarna recommend it, but beside in a short corridor.)
No problems with having only the searching wire activated.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)

Gesperrt

Zurück zu „Bug?“