Hi, sorry for typing in english.
I have automower 315 (2015) and FW Beta 7a.
I discovered that return to base via boundary line ONLY works if both settings are active and have the same value (boundary: return to base-right, return to base-left).
Meaning that the mower don´t follow the boundary line to the base station if the value is´t equal, or if only one option is checked (active).
SW7a-Return to base via boundary line problem [POSSIBLE BUG, UNRESOLVED]
-
- Forum-Anfänger
- Beiträge: 3
- Registriert: Mi 28. Jun 2017, 09:09
- Mäher: Husqvarna Automower 315
- Herstellungsjahr: 2015
- Robonect-Modul: Robonect Hx (Rev.4)
- Robonect Firmware: beta 7a
SW7a-Return to base via boundary line problem [POSSIBLE BUG, UNRESOLVED]
Zuletzt geändert von shadowkiller am So 23. Jun 2019, 16:58, insgesamt 2-mal geändert.
Grund: Titel vorläufig an aktuellen Status angepasst
Grund: Titel vorläufig an aktuellen Status angepasst
-
- Administrator
- Beiträge: 2907
- Registriert: Di 19. Jan 2016, 18:34
- Wohnort: Kiel
- Mäher: Gardena SILENO City 500
- Firmware des Mähers (MSW): MSW 11.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: stets die Allerneuste :-)
- hat sich bedankt: 1 Mal
- wurde gedankt: 60 Male
- Kontaktdaten:
[ZU BESTÄGTIGEN] SW7a-Return to base via boundary line problem
Can someone with a Automower 315 confirm this?
If so, i will combine left and right boundary.
If so, i will combine left and right boundary.
Werbefläche zu vermieten.
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Re: SW7a-Return to base via boundary line problem
I’ll test it today... please standby
O.k. tested!
The users manual describes the following and is confirming this, too: boundary wire activated for finding the charging station the mower randomly decides which direction it will follow right or left side along the boundary wire. So ist doesn't matter for Robonect settings: only one checkbox for the boundary wire itself is needed.
Notice: following the boundary wire worked for me, but docking in the charging station only worked having the stations radio signal on, too. Without this, the mower just ignored its existence (maybe because my station is not located on the lawn like Husqvarna recommend it, but beside in a short corridor.)
No problems with having only the searching wire activated.
O.k. tested!
I can confirm this. The only way to make it work, is to have both active. Having only one side active in robonect it results in endless searching without moving along the boundary wires but crossing them like in mowing mode. The reverse test draws the same picture: if test right or left is started in the mowers display it results in both sides activated in robonect, however I deactived both in Robonect and saved this settings.Toomaster hat geschrieben: ↑Do 11. Apr 2019, 14:01 I discovered that return to base via boundary line ONLY works if both settings are active and have the same value (boundary: return to base-right, return to base-left).
Meaning that the mower don´t follow the boundary line to the base station if the value is´t equal, or if only one option is checked (active).
The users manual describes the following and is confirming this, too: boundary wire activated for finding the charging station the mower randomly decides which direction it will follow right or left side along the boundary wire. So ist doesn't matter for Robonect settings: only one checkbox for the boundary wire itself is needed.
Notice: following the boundary wire worked for me, but docking in the charging station only worked having the stations radio signal on, too. Without this, the mower just ignored its existence (maybe because my station is not located on the lawn like Husqvarna recommend it, but beside in a short corridor.)
No problems with having only the searching wire activated.
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)