Since installing beta 7, I've had intermittent problems with the mower not registering the search and work hours in either Robonect or in the R40 service menu.
The totals are increasing, just not the individual timers.
Also - is there some kind of ETA on beta 8 or a possible release version of 1.0?
Best,
David
Beta 7 does not register individal search and work hours [NO BUG]
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Beta 7 does not register individal search and work hours
Do you use the moving time adjustment feature in settings/mowing behavior?
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
- shadowkiller
- Forum-Veteran
- Beiträge: 4475
- Registriert: Do 11. Jan 2018, 08:42
- Wohnort: Würzburg
- Mäher: Husqvarna Automower 315
- Firmware des Mähers (MSW): MSW 10.xx.xx
- Herstellungsjahr: 2017 (Modell 2018)
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.3 (WLAN 1.7.4)
- hat sich bedankt: 160 Male
- wurde gedankt: 135 Male
Beta 7 does not register individal search and work hours [NO BUG]
The data you’re demanding are normally saved by the mowers software, Robonect only shows them.
But because Robonect uses workarounds to realize the mowing time adjustment feature exclusively for Robonect users, the mower is unable to collect and also to save this kind of data and as reason of this, Robonect is unable to show this data.
I hope you can understand this also of my bad English
But because Robonect uses workarounds to realize the mowing time adjustment feature exclusively for Robonect users, the mower is unable to collect and also to save this kind of data and as reason of this, Robonect is unable to show this data.
I hope you can understand this also of my bad English
Anleitung zur Erstinstallation
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
--
Robonect® Dokumentation (= Gebrauchsanweisung = Bedienungsanleitung) und Support
--
Forum cooler nutzen: Hervorhebungen machen und Screenshots posten
--
Es wurde schon alles gefragt, nur noch nicht von allen. (frei nach Karl Valentin)
-
- sehr erfahrener Forum-Nutzer
- Beiträge: 120
- Registriert: So 26. Mär 2017, 11:31
- Wohnort: Sweden
- Mäher: Gardena smart SILENO
- Robonect-Modul: Robonect Hx (Rev.5)
- Robonect Firmware: 1.4
- hat sich bedankt: 6 Male
- wurde gedankt: 20 Male
- Kontaktdaten:
Re: Beta 7 does not register individal search and work hours [NO BUG]
Noted.
And for the record, your english is good.
And for the record, your english is good.
Best regards,
David from Sweden
David from Sweden